Finally, I have a full post for you. I was hoping to get this post up in a day, but it has taken a few extra days to put this post together. It has lots photos and hope you will find it useful! I bough the 1500 pieces of 3/4" hexagon paper piecing when I was trying to make the grandmother quilt three years ago. The package has been saved for a long time and I have a small project in mind and these hexagons are great of it. I'd like to show you how I baste and piece the fabric and paper piecing together.
I am a visual person! Usually I like to map out things around when I sew. I could have done a simple math, but I though put the hex pieces out and measure them together by an actual ruler would be more clear.. Here are total of 60 pieces of 3/4" hexies.When they are all joined together will give a roughly 9"x10". I ordered my paper piecing from
here.
Select your fabric prints. With 3/4" size hexagon. I cut my fabrics into 2"x2" squares.
Lay your paper piecing on top of the fabric piece.
Trim the four corners. It will give clean look in the back when you fold them. Often time I might put three pieces together and carefully trim four corners together. I always put a piece of paper on top, so I can get nice cuts around the paper.
Fold the top of the fabric side down { Some tutorials show to used paper clips or sewing pins to held the paper and fabric in place, but I go without both of tools}. You might find using paper clips and sewing pins helpful, so I encourage you try out and see what fits you the best!
Let your needle go through paper and fabric together. {I used embroidery needles for the basting. I found the thinner needles work better, but you may just use what's available for you}.
Then you will turn your fabric and paper work clockwise for the second fold. The folding corner { where my fingers were} will overlap the first fold fabric and the second fold fabric.
Use the needle from the back then go through the fabric and paper. This time your needle will go through the overlap fabric{ Hope this explain clear, but let me know it is confused}.
Fold your third side of fabric then go through with your needle. There will be total of six folds until you finish.
At the last fold. I like to give it a small pull.
Tied a little knot and you are done!
Repeat the same method for your other hex pieces.
After finished all the pieces. Play with them... ..
The back of each fabric and paper piece..
Pick two pieces of the hex then put them right side together. Make sure corner point to corner point.
Use your needle go through the corner points. I like to double my thread , but you might just use a single tread for this part.
After the needle went through the first time. I always go through the same corner point the second time to reinforce the join corner points.
Take your needle and slowly go around the side. It is like stitch in loops.
When you finish the side. It would look like this. Many small stitches.
At the end, tied a small knot to finish your stitch.
Here is the small knot.
I always take my needle and go under the folding fabric to hide the knot that I just made.
It gives a clean and reinforcement.
You will repeat the same join method for how many pieces you need.
The back for the hexagon would look like this { Later on, the paper will be take off}.
Should we keep going??
I always match the hexagons before I start my stitches. So I would have ideas about which side would match to each other.
Take the stitched piece then put it down to match the other piece and put them right side together.
Use needle then stitch both hexagon corners together. Again, I doubled loop the corner, so it is reinforced.
You would do the loops again on the side.
Once you get to the second corner point. Be extra careful to give another double stitches.
Then you'll need to turn your paper to match the second side of hex together { right side together}.
I found single thread works better on this part. Since there are many loops you have already make. Single thread would be easier. When I did the single thread, the loops were even closer to each other, so it gives same strenght as double thread.
Again, double loop in the corner points.
You would continune the same method till you finish the hexagons.
As the piece gets bigger, you will find it is a little hard to work. In the past, I would start taking the paper off, but this time I save them. I folded the paper around, so it wasn't really an issue.
Once you have all the hexagons pieces. the back would look like this.
Now! Time to take papers out.. I like to use my seam ripper for this part. Be extra careful! You have just hand stitched all the pieces together. I'd say, it is delicate, but strong as well! You will find you need some time to take these paper and basted thread out.... take you time!
Once you have all the paper out and thread clean. You will see the sides around is off the folding look.
Give a gentle iron press. Refold the sides before you press! Make them look good, since you have work so hard to get this far!! Now you have a piece of hexagon patchwork to make into any project that you have in mind!
It took a a little longer time to put this tutorial together. I enjoy photography and give my best description here for you! If there's any step that's not clear to you.. please let me know!! Try some English paper piecing! You'll love it and it is a great portable project that you can take during your trips and doesn't take up your space. Have fun and enjoy!
xxC
